This should help you get your dreambox Up and running with a USALS, STAB or
DISEQ 1.2 Motor.
Requirements: beta 104 or later of Firmware - If you are unsure, look in the
SETUP>Channels menu and see if there is an entry for "Rotor Setup..." you
are Elected!!! If Not - Isn`t it time you Upgraded??!!
Optional But Cool: My latest "Satellites.Xml" file for your dreambox to
expand it`s Satellite Scanning Selection. (the stock file from DREAM has
only a few)
## Firstly, go to the SETUP>CHANNELS>SATELLITES menu:
Use NEW to add all the satellites you can recieve.. When you select NEW,
another entry will be added to the end of the list shown.. Move down onto
the new entry and hit OK, a drop-down menu will allow you to select the
satellite you want from the list (read from "satellites.xml").. Add the ones
you want and Make sure they are all on LNB 0.
## Then make sure the Rotor is set correctly:
Move to the Symbol For LNB 0 and hit OK.. then BLUE button, the settings
should be:
Minidiseq param: None,
Mode: 1.2,
Param A/A,
Repeats: None
Save(green button) and CLOSE
## Then go to the SETUP>CHANNELS>ROTOR SETUP menu:
We Don't use ROTOR INPUT POWER or GOTOxx for this method.. We are going to
rely on Selecting Presets in the Rotor..
The time Value in the upper right is for "degrees moved per second", 1.000
is a good medium.
You need to enter the Rotor Preset Numbers for the satellites you have
installed in the previous menus.. Example: Number in rotor: 6 , Orbital
Position: 50 , Direction: EAST then ADD will make an entry for Sirus - 5
degrees east, Factory Preset 6 in Diseq motars, which will appear in the
table to the left of the screen as "6 / 050 E". You need to do this for all
the satellites in the rotor's preset list. All motars Claiming to be USALS,
STAB or Diseq 1.2 have these presets in memory, unless you have overwritten
them!!
You may prefer to REMOVE any that are there when you start, then maybe set
up just 2 to test the system.. Hotbird & Astra are the classics
1 - Hotbird 13E
2 - Astra 19.2E
3 - Eutalsat 16E
4 - Eutalsat 10E
5 - Eutalsat 7E
6 - Sirus 5E
7 - Telecom 3E
8 - (Thor 0.8W)Intelsat 1W
9 - Telecom 5W
10 - Telecom 8W
11 - Intelsat 18W
12 - NSS K 21W
13 - Intelsat 27W
14 - Hispasat 30W
15 - Orion 37W
16 - Astra 23.5E
17 - Arabsat 26E
18 - Astra 28.2W
19 - Kop 28E
20 - Arabsat 30E
21 - Turksat 31E
22 - Turksat 42E
23 - Intelsat 34.5E
24 - Pas 45W
25 - Amos 4W
26 - Thor 0.8W
27 - Nilesat 7W
28 - Atlantic 12.5W
Note: Remember orbital positions are entered like this: 0.8W is entered as
Number in rotor: "8" and Orbital Position:"8", for Preset 8 at 0.8w,
19.2east as "2" and "192", 5.0east as "6" and "50" etc..
Any other positions you have found and have stored in the motor under other
preset numbers can be entered in the same way.. for example, i have telstar
15w stored on preset 27, so i have the following entry visable in my table :
"27 / 150W"..
Once you have some satelites set up on the Rotor Config Page, SAVE (green
button).
## now go to SETUP>CHANNELS>TRANSPONDER SCAN to test it all!
In the AUTO SCAN menu, hit OK over the "Network" drop-down menu to choose
your target satellite for the scan. After selecting the satellite you want,
the box will appear to freeze, this is because it's waiting for the rotor to
move to the selected position before trying to decode anything.. This is not
a freeze as such, but a delay, as set in the ROTOR CONFIG menu.. When it
comes back to life your DB will start running throught the Transponders
listed in the "satellites.xml" file trying to find an active one - when it
does you'll get the LOCK & SYNC indicators on and you can scan.. "ERASE ALL"
will only erase channels from that satellite, not your entire listing
All of this depends on what satellites you have installed in your
"satellites.xml" file.. if there isn`t an entry for a satellite, it wont
appear in the SETUP>CHANNELS>SATELLITES menus, and you won`t be able to
associate channels with Diseq Presets.
It`s best to always use the grammer you find in the
SETUP>CHANNELS>SATELLITES entrys for your table in ROTOR CONFIG.. if the
satellite is called "Sirus 5.0E", make SURE you make the entry for it as "6
/ 050E" and NOT "6 / 052E"!! Remember the motor Doesn`t care what you enter,
it is only responding to a call for a preset, it`s the Dreambox that nees to
have clear grammer to make the association between the Rotor setup Entry and
the Actual entry in the "satellites.xml" file.. just a point for the
homebrewers out there! You can eliminate this worry by installing my fab
"satellites.xml" file - available now where you found this information
(probably).
This Is fully working With STAB HH100i [Diseqc 1.2] and STAB HH120 [Diseqc
1.2 & Stab-USALS], Dreambox Firmware beta 1.0.4 27.12.2002 and
satellitesxml_dreambox_170103.zip .xml file.
Thanks to -[marta]-
Satellite City
http://www.satcity.nl
Post by CarpNece mi vrtit motor, na starom reciveru mi normalno radi.
Mozda neko zna u cem je problem?